P0152 harley code after cam install how to#
P0152 harley code after cam install serial#
P0152 harley code after cam install driver#

The programmed dwell feature gives adequate spark at all speeds.ĮCT – Engine Coolant Temperature. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.ĮCM – Electronic Control Module.

P0152 harley code after cam install serial#

U1255 Serial Data Error/Missing Message TSM/TSSMĬKP – Crank Position Sensor. U1255 Serial Data Error/Missing Message Instruments U1255 Serial Data Error/Missing Message EFI

U1097 Loss of Speedometer Serial data TSM/TSSM U1097 Loss of Speedometer Serial Data to ECM U1097 Loss of Speedometer Serial data EFI U1097 Loss of Speedometer Serial data Carb U1064 Loss of TSM/TSSM Serial Data Instruments U1064 Loss of TSM/FSFM Serial Data to ICM / ECM U1016 Loss of ICM/ECM Serial Data Instruments U1016 Loss of ECM Vehicle Speed, Vehicle Inhibit Motion or Powertrain Security Status TSM/TSSM P2138 TGS Correlation Error (Twist grip sensor) P2119 EFI Motor Throttle Body Range Performance P2107 EFI Module Processor Internal Fault P2101 EFI Motor Circuit Range Performance (Actuation Error) P1600 EFI Module Processor Internal Error P1358 Rear Cylinder Combustion Intermittent P1357 Front Cylinder Combustion Intermittent

P0152 harley code after cam install driver#

P1355 Rear Ignition Coil Driver High/Shorted Downsides The instructions for installation are OK, but my dealer was worthless when it came to setting this thing up. It is like having a parts-bin full of carb jets, but takes only seconds to change settings. P1352 Front Ignition Coil Driver High/Shorted

P0152 Harley Code After Cam Full Of Carb P0152 Harley Code After Cam Full Of Carb.

P1351 Front Ignition Coil Driver Open/Low P0106 MAP Sensor Rate of Range Error Carb Here are some of the various diagnostic trouble code lists (DTCs) used on ICM/ECM equipped HD models through 2008:ī1004 Fuel Level Sending Unit Low Instrumentsī1005 Fuel Level Sending Unit High/Open Instrumentsī1006 Accessory Line Overvoltage Instrumentsī1007 Ignition Line Overvoltage Instrumentsī1121 (TSM) Left Turn Output Fault – (HFSM) Left Turn Output Openī1122 (TSM) Right Turn Output Fault – (HFSM) Right Turn Output Openī1123 (HFSM) Left Turn Output Short to Groundī1124 (HFSM) Right Turn Output Short to Groundī1125 (HFSM) Left Turn Output Short to Batteryī1126 (HFSM) Right Turn Output Short to Batteryī1136 (HFSM) Accelerometer Tip Test Errorī1141 (TSM) Ignition Switch Low/Open – (HFSM) Ignition Switch Low/Openī1142 Smart Security System Internal Faultī1143 (HFSM) Security Antenna Short to Groundī1144 (HFSM) Security Antenna Short to Batteryī1151 Bank Angle Sensor(BAS) Short to Groundī1152 Bank Angle Sensor(BAS) Short to Batteryī1154 Clutch Switch Input Short to Groundī1155 Neutral Switch Input Short to Battery Don’t just go out and by a new sensor or part.

P0152 harley code after cam install how to#

This videos reviews how to retrieve the codes and this process will help you determine where to look and test. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes. Articles on Harley-Davidson How-to and More